Synth Pi

Having explored the inside of my Roland D10, I have decided to try and pimp it out with a Pi running Fluidsynth for a bit of fun.

Progress so far:

Installed fluidsynth:

sudo apt-get install fluidsynth

Installed ttymidi

sudo apt-get install libasound2-dev

wget http://www.varal.org/ttymidi/ttymidi.tar.gz
tar -zxvf ttymidi.tar.gz
cd ttymidi/
make
sudo make install

... then followed this from https://wiki.archlinux.org/index.php/USB_Midi_Keyboards

and have a working link to my USB controller (although slightly laggy)

Preliminary Testing

USB

First let us make sure that USB is working properly. When you type lsmod you should see some modules such as ehci, uhci or such. Also, when you type lsusb you should see something like:

Bus 004 Device 001: ID 0000:0000
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000

This list might contain some USB devices if you have them plugged in or more or less items, depending on how many USB ports you have.

ALSA

You should have ALSA set-up properly (alsa-lib and alsa-utils packages). When you type lsmod | grep snd you should see a bunch of various snd drivers.

Try typing aseqdump. If you get an error stating that "aseqdump cannot find /dev/snd/seq" or similar, you might not have the snd-seq module loaded. To rectify that, type (as root)modprobe snd-seq. You might also want to add (again as root) snd-seq to your /etc/rc.conf file in the modules list. If the module is succesfully loaded, typing aseqdump should show something like:

Waiting for data at port 128:0. Press Ctrl+C to end.
Source_ Event_________________ Ch _Data__

Not much will show up there, so press Ctrl+C to quit the program.

Plugging the keyboard

Now plug the keyboard in and turn it on. The keyboard should power up. Output of lsusb should contain:

Bus 002 Device 002: ID 0a4d:00a0 Evolution Electronics, Ltd

Output of lsmod | grep usb should contain the following modules:

usb_midi               25348  0
snd_usb_audio          70592  0
snd_usb_lib            16640  1 snd_usb_audio

Now type aconnect -i. The output should contain:

client 72: 'MK-361 USB MIDI keyboard' [type=kernel]
    0 'MK-361 USB MIDI keyboard MIDI 1'

The client number is probably going to be different though. Take note of it.

Verifying Events

Type aseqdump -p ## where you should replace ## with the client number of your keyboard. You should see:

 72:0   Active Sensing

popping out all the time. Pressing a key should produce:

 72:0   Note on                 0  65  94
 72:0   Note on                 0  65   0

Various other events (turning control knobs, changing channels, etc.) should register in the list. This is a handy way of ensuring that your keyboard is running properly.

Playing

Now type aconnect -o to list the devices listed as ALSA midi outputs. It depends a lot on your sound card. On SB Live! Value, you get the following output:

client 64: 'EMU10K1 MPU-401 (UART)' [type=kernel]
    0 'EMU10K1 MPU-401 (UART)'
client 65: 'Emu10k1 WaveTable' [type=kernel]
    0 'Emu10k1 Port 0  '
    1 'Emu10k1 Port 1  '
    2 'Emu10k1 Port 2  '
    3 'Emu10k1 Port 3  '

Here client 65 is the actual MIDI synthesizer. Assuming the soundcard is set up properly, you should be able to route the output of the keyboard to the MIDI synthesizer. Assuming outis the output client number (65 in our example) and in is the input client number (72 in our example), type aconnect out in. Now you can play your keyboard via the MIDI output of your sound card.

To get it all working, I started Fluidsynth with:

fluidsynth -C0 -R0 -r22050 -a alsa /usr/share/sounds/sf2/FluidR3_GM.sf2

and in a ssh terminal I ran:

aconnect 20:0 128:0